IssueDownload Driver for Cable SR2USB01Product Line:Cable SR2USB01Environment:Zelio Smart RelaysResloution:There is a specific driver available for the Windows 7 (64bits) available for the cable SR2USB01 which so far is not integrated with Zelio Soft.The pre condition to use the Zelio soft and the SR2USB01 cable to use on windows 7 is to have the V4.5.0 of Zelio Soft installed on the computer.You can download and install this software from the following link: _V4_6_light/Further the Driver for USB cable for Windows 7 can be downloaded from the following link: _USB-Driver-W7-64-bits_V1_0/This Driver Zip file also contains the information regarding installation of the USB cable driver on the PC.Please follow the above steps and review the following video for proper installation of the driver.
IssueDownload Driver for Cable SR2USB01Product Line:Cable SR2USB01Environment:Zelio Smart RelaysResloution:There is a specific driver available for the Windows 7 (64bits) available for the cable SR2USB01 which so far is not integrated with Zelio Soft.The pre condition to use the Zelio soft and the SR2USB01 cable to use on windows 7 is to have the V4.5.0 of Zelio Soft installed on the computer.You can download and install this software from the following link: -electric.com/en/download/document/ZelioSoft2_V4_6_light/Further the Driver for USB cable for Windows 7 can be downloaded from the following link: -electric.com/en/download/document/Z2_USB-Driver-W7-64-bits_V1_0/This Driver Zip file also contains the information regarding installation of the USB cable driver on the PC.Please follow the above steps and review the following video for proper installation of the driver.
sr2 usb01 driver windows 7 64 bit zip
Download: https://urluso.com/2vKKYE
I have a few handheld radios that I need to update the frequencies and when I connect to the USB, it fails to connect. In device manager and Ports it says - "Please install corresponding PL2303 driver to support Windows 11 and further OS"
There is a working driver at _id=225&pcid=41, a bit down the page listed as "DCHU (for PC Vendors)". Getting it installed is a bit tricky, it seems. What I did is this:First install the downloaded driver by unpacking the zip file and "pnputil /add-driver *.inf /subdirs /install" (the /install is probably not necessary) from the extracted "Win11_DCHU" directory. It will add the two driver packages to the driver store and tell you what oemXY.inf files it has assigned to them.Then "pnputil /enum-drivers", and in the output look for Prolific drivers other than the ones from the previous step. I had only one other entry, a "ser2pl.inf" version "09/16/2021 3.8.40.0".Disconnect the device, and "pnputil /delete-driver oemXY.inf" with the INF file you located in the previous step.Connect the device again, and it should work, at least, it does for me. The problem is probably that the non-working driver is the newest (September 2021 vs. July for the ones from the download page) and so Windows prefers it over them.
Windows 11 update loaded Prolific PL2303 driver 3.8.40.0 and when I go to device manager it says "Please install corresponding PL2303 driver to support Windows 11 and further OS" This driver does not even attempt to communicate with my X10 CM11 hooked to my serial port. I had to go to Prolific website and load their current driver 3.6.81.357. (uninstall driver first) Serial to X10 device now working fine. Don't install Windows update for Prolific or it will change it back.
I work with plcs. After the upgrade I'm having some communication error with one of such plc. My Schneider Zelio Soft 2 plc software, version 4.6 and Zelio Smart relay(plc) was working fine with my previous windows 8.1. I had no issues transfering the plc program to the module(plc). Now with windows 10 I can't establish a communication between the software and the module(plc). Every time I attempt a communication the screen turn blue with error message: 'unexpected kernel mode trap' and goes to restart mode. I've no problem opening the software and working with it in windows 10.
The only problem is with the communication with module. I'm suspecting the usb to serial driver that is not compatible with windows 10. The software and the usb driver can be found in the Schneider Electric website.
Hi, Sure sounds like a driver or other incompatibility issue to me. Try this: Control Panel - Device Manager - find the device(s) and double click on them Driver tab - click Update driver (probably will do nothing) - when complete Right Click on and UNINSTALL - when complete reboot. If no help then Re-install the drivers using compatibility mode: Download the latest available drivers from the maker's website.
Right Click the setup.exe (installable file if a ZIP unpack first) - click properties then the Compatibility tab. Check Run in Compatibility mode - select the OS same as your driver. Hope this helps. Rob Brown.
2ff7e9595c
Kommentare